Kohler CV1000 Bedienungsanleitung Seite 37

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 138
  • Inhaltsverzeichnis
  • FEHLERBEHEBUNG
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 36
5.9
Section 5
Fuel System and Governor
5
Figure 5-14. Float and Inlet Needle Details.
ȱ Ŝǯȱ ȱȱĚȱȱȱȱȱȱȱ
seat and carburetor body. Install the new pivot
ȱȱȱĚȱȱȱȱȱȱ
ȱȱǯȱȱȱśȬŗśǯ
Figure 5-15. Installing Float Assembly.
ȱ ŝǯȱ ȱȱȱ¢ȱȱȱĚȱ¢ȱ
hangs vertically and rests lightly against the
fuel inlet needle. The inlet needle should be
fully seated but the center pin of the needle (on
retainer clip end) should not be depressed. Check
ȱĚȱȱǯ
DZȱ ȱȱȱȱȱȱȱ
ǯȱȱȱȱĚȱȱȱ
the fuel inlet needle without depressing
the center pin.
ȱ Şǯȱ ȱȱĚȱȱĴȱȱ17 mm (0.669
in.) ± 1.5 mm (0.059 in.)ǰȱȱȱȱĚȱ
Ĵȱȱȱ¢ȱȱȱǯȱȱȱ
śȬŗŜǯȱȱȱĚȱȱȱȱȱěȱ
ȱęǯȱDO NOTȱĴȱȱȱ¢ȱ
ȱĚȱǯ
DZȱ ȱȱȱȱȱȱȱ
surface, not the rubber gasket, if still
Ĵǯ
Figure 5-16. Checking Float Height.
ȱ şǯȱ ȱȱȱĚȱȱȱǰȱ
carefully reinstall the fuel bowl, using new
Ȭȱȱȱǯȱȱȱȱȱ
original screws. Torque the screws to
2.5 ± 0.3 N·m (23 ± 2.6 in. lb.)ǯȱȱȱśȬŗŝǯ
Figure 5-17. Installing Fuel Bowl.
10. Install the carburetor and reassemble the engine
ȱȱȱȱŗŖȱȃ¢ǯȄ
Disassembly/Overhaul
1. Clean the exterior surfaces of dirt or foreign
material before disassembling the carburetor.
Remove the four mounting screws and separate
the fuel bowl from the carburetor. Transfer any
remaining fuel into an approved container.
ȱȱȱȱȱȬǯȱȱ
can also be drained prior to bowl removal by
Ȧȱȱȱȱȱǯȱȱ
ȱśȬŗŞǯ
Float
Inlet
Needle
Clip
Retaining
Screw
Pivot
Pin
Seitenansicht 36
1 2 ... 32 33 34 35 36 37 38 39 40 41 42 ... 137 138

Kommentare zu diesen Handbüchern

Keine Kommentare