Kohler Discovery Bedienungsanleitung

1These instructions are to be left with the userInstallation and User GuideSHOWER VALVEBUILT IN DUAL CONTROL

10INSTALLATIONGeneralInstallation must be carried out in accordance with these instructions, and must beconducted by designated, qualified and compete

11Installation MethodsThe Discovery Thermostatic Shower Controlcan be installed using Rear Fixing Pointson the Body, or by using the SecuringBrackets

121. Solid Wall or Stud Partition(Using Securing Brackets - Mounting off Front Face)1.1 Remove the three securing screws andremove the shower valve fr

131.7 Fit the three securing brackets to theshower valve.Important! Make sure that the correctholes are used, otherwise thebackplate will not fit (ref

141.14 Re-fit the building-in shroud to the shower valve using the three fixing screws.1.15 Using the building-in shroud as a guide for the finished w

152. Solid Wall or Stud Partition(Using Rear Fixing Points on Shower Control)2.1 Refer to section: ‘1. Solid Wall orStud Partition Installation (Using

162.3 Mark the positions of the fixing screwholes on the wall.2.4 For solid walls drill two 6 mm holes forthe wall plugs.2.5 Fit the wall plugs (suppl

17Note! For laminated panels the showervalve must be positioned from the rear ofthe panel.Panel thickness must be between 4 and22 mm (if a thicker pan

183.6 To assist in marking the positions ofthe fixing holes, reverse the showervalve and fit the building in shroudthrough the cutout in the front of

19Control Assembly1. Pull off the temperature knob.2. Carefully separate the concealing platefrom the backplate.Note! Use a screwdriver in the cutoutt

2CONTENTSIntroduction ... 3Safety : Warnings ...

20Push up and Latchover the Top of theBackplateAlign Flow Leveras Shown‘Click’ into Position5. Align the flow control lever so that thelever is pointi

21Reversed SuppliesThe Discovery Dual Control is supplied with inlet connections Hot-Left, Cold-Rightand Top-Outlet as standard. If the hot and cold w

22COMMISSIONINGMaximum Temperature SettingThe Thermostatic Shower Controls are preset at approximately 43 °C at the factory.If adjustment is required,

23OPERATIONNote! If excessive flow rate is experienced from the Shower Control, install the suppliedFlow Regulator, refer to the Discovery Fittings In

24FAULT DIAGNOSISSYMPTOM1. Only hot or coldwater from the controloutlet.2. Fluctuating or reducedflow rate.3. No flow rate from thecontrol outlet.4. B

25‘O’ KeySupply FilterMAINTENANCEGeneralThis Product is precision engineered and should give continued safe and controlledperformance, provided:1. It

26SPARE PARTS1609.040 (A) Thermostatic Cartridge Assembly1609.041 (B) Elbow Pack (2 off)1609.042 (C) Flow Control Assembly1609.043 (D) Flow Contro

27JABCC, K, JDDDEGIL K, J

287-#51058366-W2-A(1609)© Kohler Mira Limited, February 2006CUSTOMER SERVICE

3This Discovery Thermostatic Shower Control is precision engineered and should givecontinued safe and controlled performance, provided:1. It is instal

4 1 x Control Assembly Tick the appropriate boxes to familiarize yourself with the Discovery ThermostaticShower Control part names and to confirm t

5DIMENSIONSNote! All Dimensions are NominalPipe Centres186 mm47 mm 64 - 82 mm108 mm231 mm27 mm

6SPECIFICATIONSPressuresMaximum Static Pressure: 10 Bar.Minimum Maintained Pressure (Gas Water Heater): 1.0 Bar.(for optimum performance initial suppl

7ConnectionsStandard connections are: Hot-Left, Cold-Right, Top-Outlet, if reversed inlets arerequired refer to sections: ‘Installation’ and ‘Reversed

8Flow Regulator RecommendedINSTALLATION REQUIREMENTSIsolating valveMixing ValveTwin Impeller PumpTempering ValvePressure Reducing ValveSingle Impeller

9Flow Regulator RecommendedFlow Regulator RecommendedUnvented mains pressure systemThe shower can be installed with aunvented, stored hot water cylin