Kohler K-97611-T01-96 Installationsanleitung PDF herunterladen (Seite 2)

Top View

Shallow

Channel

Deep

Channel

Corner

Joints

Construction

Adhesive

Construction

Adhesive

Shims

54" (1372 mm)

(not shown)

40"

(1016 mm)

36"

(914 mm)

24"

(610 mm)

Robe Hook

Flip Down Seat

Handrails

Handrail Shelf

7" (178 mm)

14" (356 mm)

21" (533 mm)

Shelf

Shim

Corner

Joint

Seam

Joint

7/8"

(14 mm)

Side View

Top View

Back Wall with Joints

Shallow

Channel

Sealant

Deep Channel

Sanding Block

Back Side

KOHLER® Limited Warranty — Choreograph™ Walls and Accessories

Kohler Co. warrants all Choreograph™ products (including Choreograph™ accessories) to be free of defects in

material and workmanship during normal residential use for ten (10) years from the date of sale. If a Choreograph™

product or accessory is used commercially or is installed outside of the United States of America, Canada or Mexico,

Kohler Co. warrants the Choreograph™ product or accessory to be free of defects in material and workmanship

during normal use for three (3) years from the date of sale.

If Kohler Co’s. inspection of your Choreograph™ product or accessory discloses a defect in material or workmanship

within the applicable period of coverage stated above, Kohler Co. will, at its election, repair, replace or make

appropriate adjustment. Kohler Co. is not responsible for labor charges, installation, or other incidental or

consequential costs. In no event shall the liability of Kohler Co. exceed the purchase price of the Choreograph™

product or accessory. Damages due to improper handling, installation or maintenance are not considered

manufacturing defects and are not covered by this warranty. This warranty is valid for the original, consumer

purchaser only. Proof of purchase (original sales receipt) must be provided to Kohler Co. with all warranty claims.

To obtain warranty service, contact Kohler Co., either through your plumbing contractor, home center, wholesaler,

dealer, or E-tailer, or by calling or writing Kohler Co., Attn.: Customer Care Center, 444 Highland Drive, Kohler,

Wisconsin 53044, 1-800-4KOHLER (1-800-456-4537) from within the USA and Canada, and 001-800-456-4537 from

within Mexico, or visit www.kohler.com within the USA, www.ca.kohler.com from within Canada, or www.

mx.kohler.com in Mexico.

TO THE EXTENT PERMITTED BY LAW, ALL IMPLIED WARRANTIES INCLUDING THOSE OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.

KOHLER CO. AND SELLER HEREBY DISCLAIM ANY LIABILITY FOR SPECIAL, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES. Some states/provinces do not allow limitations on how long an implied warranty

lasts, or the exclusion or limitation of special, incidental or consequential damages, so these limitations and

exclusions may not apply to you. This warranty gives you specific legal rights. You may have other rights which

vary from state/province to state/province.

This is the exclusive written warranty for Kohler Co.

Troubleshooting

Symptom: A panel is not correctly adhering to

the wall or ceiling.

Recommended Action

1. Panel does not fully adhere to the wall. A. There may be vapor lock. Pull the panel out away from the wall to allow vapor to escape and press back into place.

B. Is the installation over tile? The tile should have been roughed up with sandpaper to allow a better surface for the

adhesive to grip. Remove the panel, rough up the tile, apply additional adhesive and reinstall the panel.

C. Were the wall and panel surfaces cleaned before adhesive was applied? Remove the panel and clean the surfaces.

Apply additional adhesive. Reinstall the panel.

IMPORTANT: It is critical the walls and panels

are clean for a strong bond to be created by the

adhesive.

Clean the back of the panels with denatured

alcohol.

On the edges of each panel, remove excess

material and smooth any rough edges using a

sanding block.

When wall panels fit into the corner joints, sand

the cut edges for smooth fit.

Dry fit the corner joints to the back panel if

they are being installed. (See step 14 for correct

orientation.)

Dry fit the back and sidewall panels to confirm

fit. Adjust as needed.

Remove the panels. Remove the corner joint(s).

Installations Using Corner Joint(s):

Measure the height of the back panel.

Cut the corner joint to the height of the back

panel.

Apply color matched silicone sealant in the

deep channel groove on the corner joint. Apply

enough sealant to fill 1/2 of the groove.

Installations Using Corner Joint(s):

Install the deep channel of the corner joint on the

side of the back wall piece.

Repeat for the second joint if needed.

NOTE: Use silicone sealant if the panels are

being installed over tile. Use bath and shower

construction adhesive for other applications.

Apply construction adhesive or silicone adhesive

to the back wall panel in a circular pattern.

The beads of adhesive should be 5” (127 mm) to

7” (178 mm) apart.

Apply a bead of construction adhesive along the

top edge of the back wall panel 3/4” (19 mm)

from the edge.

Move the back wall panel into place at a slight

angle.

Push the panel against the rough wall. Press

firmly and evenly across the entire wall. The

panel should contact the rough wall along the

entire area.

TIP: When removing excess silicone sealant,

spray denatured alcohol on the area with excess

sealant and your finger.

Remove the excess sealant with your finger.

Push firmly on all surfaces of the back panel for

full adhesion.

NOTE: Bracing may be needed to hold the panel

in place depending on the wall material and

adhesive being used.

When installed over tile, use a temporary brace

to secure each wall panel in place for 48 hours to

allow full adhesion.

If corner joints are installed, fill the joint 1/2 full

of color matched silicone sealant to the shallow

channel on the corner joint seam.

NOTE: Use silicone adhesive if the panels are

being installed over tile. Use bath and shower

construction adhesive for other applications.

Apply bath and shower construction adhesive to

the side wall panel (or bottom side wall panel) in

a circular pattern. The beads of sealant should be

5” (127 mm) to 7” (178 mm) apart.

Press the side panel (bottom side panel if there

are two panels) to the joints, then push the panel

firmly against the rough wall.

NOTE: Bracing may be needed to hold the panel

in place depending on the wall material and

adhesive being used.

When installed over tile, use a temporary brace

to secure each wall panel in place for 48 hours to

allow full adhesion.

Installations Using Seam Joint(s):

If a seam will be installed, determine the

required length of the seam joint.

Cut the seam joint to allow enough length to

extend into the channel of the corner joint.

Cut the seam joint to the required length.

Installations Using Seam Joint(s):

If a seam joint will be installed, trim the end of

seam joint where it will meet the corner joint.

NOTE: To trim the seam joint, a small rotary

tool with a cutting wheel is recommended.

Installations Using Seam Joint(s):

Fill one channel with color matched silicone

sealant on the seam joint and install the seam

joint to the installed wall panel.

Apply color matched silicone sealant to the

second channel on the seam joint.

Install the additional panels following the same

steps.

Repeat steps 19 through 24 with the second side

of the enclosure.

If installing end caps on the outside edges of the

panels, measure the wall panel(s) height and cut

the end caps to fit.

Apply color matched silicone sealant to the end

cap channel.

Install the end cap to the outside edge.

IMPORTANT: For better adhesion success,

allow the panels to cure 24 to 48 hours before

performing the final steps. Sealing the top and

bottom will restrict air flow, resulting in longer

curing time.

Apply sealant to the top seam where the panels

meet the rough wall.

Apply sealant to the bottom seams where the

panels meet the bath or shower base.

Install all accessories following the instructions

packed with them.

Wait 24 hours before showering or running

water.

11 12

27 28

1 2 3 4 5 6

Kommentare zu diesen Handbüchern

Keine Kommentare

Kohler K-97611-T01-96 Installationsanleitung Seite 2

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Kohler K-97611-T01-96